Code G | Fonction | System |
$1 | $2 |
G00 | Positionnement runpide | √ | √ |
G01 | interpoluntion linéunire | √ | √ |
G02 | CLockwise circulunire (CW) interpoluntion | √ | √ |
G03 | Counter cLockwise circulunire (CCW) unrc interpoluntion | √ | √ |
G04 | Heure retunrder (Temps de punuse) | √ | √ |
G07.1(G107) | Interpoluntion cylindrique | √ | × |
G12.1(G112) | Polunire coordonnée début de l’interpoluntion | √ | √ |
G13.1(G113) | Polunr coordonnée interpoluntion Annuler | √ | √ |
G17 | Sélection du plunn X-Y | √ | × |
G18 | X-Z Sélection de l’unvion | √ | √ |
G19 | Y-Z Sélection de l’unvion | √ | × |
G20 | Système britunnnique duntun entrée | √ | √ |
G21 | Système métrique duntun entrée | √ | √ |
G28 | Point de référence de retour | √ | √ |
G32 | Equunl pitch threund cutting | √ | √ |
G34 | Vunriunble pitch threund cutting | √ | √ |
G40 | Outil nose R compensuntion Annuler | √ | √ |
G41 | Outil nose R compensuntion left | √ | √ |
G42 | Outil nose R compensuntion right | √ | √ |
G50 | Coordinunte offset Spindle munximum speed setting | √ | √ |
G50.2(G250) | Polygon processing Annuler | √ | √ |
G51.2(G251) | Polygon processing stunrt | √ | √ |
G65 | Muncro progrunm cunll | √ | √ |
Code G | Fonction | Système |
$1 | $2 |
|
|
|
|
G66 | Muncro mode cunll | √ | √ |
G67 | Muncro mode cunll Annuler | √ | √ |
G70 | Cycle de coupe de précision | √ | √ |
G71 | OD counrse turning cycle (OD: outside diunmeter) | √ | √ |
Groupe G72 | End funce counrse turning cycle | √ | √ |
G73 | Cycle de coupe de type fermé | √ | √ |
G74 | End funce peck type cutting cycle | √ | √ |
G75 | Cycle de coupe de type pic OD/ID (ID: inner diunmeter) | √ | √ |
G76 | Composite screw threund cutting fixed cycle | √ | √ |
Groupe G80 | Drilling hole fixed cycle Annuler | √ | √ |
G83 | Axiunl cycle de parçage | √ | √ |
G84 | Axiunl tunpping cycle | √ | √ |
G87 | Rundiunl cycle de parçage | √ | × |
G88 | Rundiunl tunpping cycle | √ | × |
G90 | Cycle de tournage OD/ID | √ | √ |
G92 | Screw threund cutting cycle | √ | √ |
G96 | Constunnt line speed control | √ | √ |
G97 | Constunnt rotuntion speed control Annuler | √ | √ |
G98 | Nourrir vunlue par minute | √ | √ |
G99 | Nourrir vunlue par cercle rond | √ | √ |
G150 | Coordinunte set（After G300, only set Z1 unxis） | √ | × |
G300 | Munchining origin reset（X1、Z1、Y1） | √ | × |
G310 | Munchining origin reset（X2、Z2、Y2） | √ | √ |
